The every day things from Thalamus' life.

Thalamus' Blog

31 December, 2016

Even more progress

Filed under: Pinball — Thalamus @ 06:32

So, the ugly beast has got some legs now. Added a button and put in the long awaited coin door. Did play for a couple of hours last night. Was very fun even thouh I haven’t connected any of the DOF hardware.

Suddenly the power went and all kind of weird stuff started to happen. At first I didn’t manage to get the backglass monitor start. Once that was resolved – and I don’t know why it came back all of a sudden, then PinballX, the frontend that I’m using is refusing to start.

Hope to get it up and running again today. No clue what might cause it.

• • •
 

28 December, 2016

Even more progress

Filed under: Pinball — Thalamus @ 21:05

Might not look to be much difference from yesterday, but now at least the buttons are attached. I still have to cable them to the controller. I’ve decided to first get the computer up and running and only connect the plunger/nudge controller. Once that is working I’m going to attach the DOF controlled kit.

• • •
 

26 December, 2016

Progress

Filed under: Pinball — Thalamus @ 20:10

Looking at earlier pictures it may seem that I haven’t done much lately. Well, both true and false. I had some issues that isn’t fully resolved. The pf monitor is attached to a VESA bracket. But, this bracket is still allowed to move too easily. What you don’t see is that the legs – all of them has been attached. I planned to put the rest of the hardware into the cab, but, since the original measurements are 18mm plywood and I’ve run with 15mm. That requires me to shim some of the parts in order to make them fit. The flipper buttons are one of these.

I almost 100% sure now, where to put flipper holes but decided that I’ll wait after I’ve been to the shop and know if I’m able to get some solution for my missing 3mm. I will need to do some test cuts for the plunger as well.

So, to put it short. Complete all wood stuff before attaching the rest of the hardware. Don’t want a computer full of crud.

• • •
 

24 December, 2016

Started putting the cabinet together

Filed under: Pinball — Thalamus @ 04:31

So, I’ve started putting the cabinet together and I must say – it is looking good so far.

• • •
 

22 December, 2016

Backbox is ok

Filed under: Pinball — Thalamus @ 16:20

Measured the difference of the main cab and it is exactly 3cm. So 2 times 15mm equals the difference. That mean, if I’m not mistaken the fault lies in the non existing 45 degree cuts.

So, I checked the drawings. There where no mentions of 45 degree cuts for the back-box, so, it did a quick measurement. Seems ok to me. I went upstairs and verified the width by placing the hand rail onto the front panel cut. It fitted snugly.

So, soon I’m off again to get that darn 45 degree cut.

Update: 45 degrees cut correctly. Looks to be fitting – but, too tired to start the build today. Beers where calling my name. Haven’t had a good night sleep in days, so, hopefully that will happen tonight and I will be able to start early tomorrow while my wife is at work. I still have some days left of my holiday.

• • •
 

Cabinet parts produced

Filed under: Pinball — Thalamus @ 14:35

My colleague, Marius, helped me today to cut the cabinet parts. It’s has arrived at my apartment about half an hour ago. We pondered a bit about the sizes from the Williams Widebody drawings since the material used where 18mm instead of 15mm that we had available.

When I put the base cabinet parts together it became quite obvious that something is not 100% correct. The drawing state that we should cut the corners at an 45 angle degree, That can explain some of the reason why the total length looks to be slightly off. And the wood itself is of course when you just mock it up like this – stealing some length as well.

I’ll have to ponder a bit about what to do next. I can’t really cut the sides to smaller lengths either because of the metal rails I have for the glass cover.

Hmm.. To be continued … 🙂

Willams Widebody

• • •
 

6 December, 2016

Windows and UTC bios time.

Filed under: ComputerStuff_en — Thalamus @ 06:13

Hmmm. On my gaming comp – I have a multiboot of Fedora and Win7. Time get screwed between those operation systems and by so much that network time daemons refuse to fix it. This, I’m told is the fix to make Windows use UTC Bios time.

Windows Registry Editor Version 5.00
 
[HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\TimeZoneInformation] “RealTimeIsUniversal”=dword:00000001
• • •